Stator Pigtail Harness Connector for Polaris Sportsman 570 850 2012-2025: A Small Fix That Gets Your ATV Charging Again
Your Polaris Sportsman was running fine — until it wasn’t. If the stator pigtail harness connector for Polaris Sportsman 570 850 has melted or corroded, the battery keeps going flat, the dash flickers, or the ATV won’t start at all after a ride. Before you blame the battery, or budget for a whole new stator, take a close look at that little plug. On many Sportsman 570 and 850 models, it is the weak link: heat from a failing regulator can melt it, corrode the pins, and quietly kill your charging system.
This stator pigtail harness connector for Polaris Sportsman 570 850 is the simple, low-cost fix for exactly that problem. Instead of replacing the entire stator or wiring harness, you cut out the damaged connector and splice in this brand-new pigtail — and your charging system is back in business. Here is what it does, what it fits, and whether it is the right repair for your ATV.
Published in Automotive | Updated for 2026

In this article
- Quick Verdict: Why This Stator Pigtail Harness Connector Is Worth It
- Key Features & Benefits
- Stator Pigtail Harness Connector for Polaris Sportsman 570 850: Specifications & Compatibility
- Who Is It For?
- Stator Pigtail Harness Connector for Polaris Sportsman 570 850: Pros and Cons
- Stator Pigtail Harness Connector for Polaris Sportsman 570 850: Installation Tips
- Frequently Asked Questions (FAQ)
Quick Verdict: Why This Stator Pigtail Harness Connector Is Worth It
If your Sportsman 570 or 850 (2012–2025) has a melted, burnt, or corroded stator connector, this RMSTATOR pigtail harness is one of the cheapest and most sensible repairs you can make. It replaces only the damaged connector, it includes heat-shrink tubing for sealed splices, and it needs only basic tools and minimal mechanical experience. In fact, for a small part, it can save you the cost of a whole new stator or wiring harness.
Key Features & Benefits
- Direct repair for a melted stator connector — replaces the damaged plug instead of the whole stator or wiring harness.
- 540 mm (21 in) wire length gives you plenty of room to route the harness and make comfortable splices.
- Three heat-shrink tubes included for sealed, weather-resistant splices that stand up to mud and water.
- Brand-new connector and pigtail harness from RMSTATOR (SKU RMS957-106082), and it directly replaces Polaris part 4015340.
- Minimal mechanical experience required — a straightforward cut, splice, and seal job with basic tools.
- Wide Polaris fitment — made for Sportsman 570 and 850 models from 2012 to 2025, and also listed for Ranger 570, Scrambler 850, Sportsman 900, and RZR 1000. Always confirm your model and year before ordering.
Stator Pigtail Harness Connector for Polaris Sportsman 570 850: Specifications & Compatibility
| Brand | RMSTATOR |
| Model / SKU | RMS957-106082 |
| Replaces OEM part | Polaris 4015340 |
| Wire length | 540 mm (21 inches) |
| What’s included | Connector and pigtail harness, 3 heat-shrink tubes |
| Connector type | DIN (3-pin stator connector) |
| Product dimensions | 6 x 4.5 inches |
| Item weight | 1.12 ounces |
| Fits | Polaris Sportsman 570 and 850, 2012–2025 |
| Also listed for | Ranger 570, Scrambler 850, Sportsman 900, RZR 1000 |
Who Is It For?
- Sportsman 570 and 850 owners with charging problems traced to a burnt, melted, or corroded stator plug.
- Riders quoted a full stator or harness replacement who want a far cheaper repair that fixes the actual damaged part.
- DIY owners comfortable with basic wiring — if you can cut, strip, splice, and heat-shrink a wire, you can fit this harness.
- Anyone refreshing an older Sportsman (2012–2025) and replacing worn electrical connections before they strand you on the trail.
One honest note: if you find burnt stator windings, or your regulator/rectifier has failed, this connector alone will not fix the problem. Check those parts too — but if only the plug is damaged, this is the repair to start with. If the stator itself has failed, you will need a replacement stator — see our post on the 18 pole magneto stator coil.
Stator Pigtail Harness Connector for Polaris Sportsman 570 850: Pros and Cons
| Pros | Cons |
|---|---|
| Fixes the real cause of many charging failures — a melted connector — without replacing the stator | A repair part, not a full stator — it will not fix burnt stator windings |
| Far cheaper than a new stator or complete wiring harness | Splicing is required; it is not a plug-and-play install |
| Generous 540 mm leads make routing and splicing easy | Confirm fitment for your exact model and year before ordering |
| Heat-shrink tubes included for sealed, weatherproof joints | |
| Direct OEM replacement for Polaris part 4015340 |
Stator Pigtail Harness Connector for Polaris Sportsman 570 850: Installation Tips
- First, disconnect the battery before touching any wiring.
- Cut out the damaged connector, leaving as much good wire as possible on the stator side.
- Next, match the wires one by one and splice them with the included heat-shrink tubes.
- Seal every splice fully and route the harness away from hot exhaust parts and moving components.
- Finally, reconnect the battery, start the ATV, and check the charging voltage at the battery to confirm the repair.
Frequently Asked Questions (FAQ)
Will this stator pigtail harness connector fit my Polaris Sportsman 570 or 850?
It fits Polaris Sportsman 570 and 850 models from 2012 to 2025. Double-check your model and year on the Amazon listing before ordering, and confirm it against OEM part 4015340.
What causes the stator connector to melt in the first place?
Often a failing regulator/rectifier overheats the connection, and the connector takes the heat and melts. Replacing the connector fixes the plug, but if the regulator itself is bad, replace that too — or the new connector can suffer the same fate.
Do I need to replace the whole stator?
Not if only the connector is damaged. This pigtail lets you repair just the connector instead of the entire stator or harness. If the stator windings have burnt out, though, you will need a new stator.
Is this hard to install?
No. The manufacturer says you need only minimal mechanical experience. Basic hand tools, wire strippers, and a heat source for the shrink tubes are all you need.
What is included in the box?
The brand-new connector and pigtail harness with 540 mm leads, plus three heat-shrink tubes for sealing your splices.
If a melted stator plug is keeping your Sportsman off the trail, this is the fix to check first — a small part, a small job, and a big difference to your charging system.
Affiliate Disclosure: As an Amazon Associate, I earn from qualifying purchases at no additional cost to you.


